Anvil stand with vise11/16/2023 The hollow center also helps it sit flat on uneven surfaces. I can not tell it from a solid section of log in use. This is a hollow light weight stand that is VERY solid. When this photo was taken for a magazine I had not put the blocks on that keep the anvil in place. This is the style of stand I have been using for 28 years. There are a lot of ways to adapt this design to suit yourself. The tool holding strap could also be a strip of hardwood. To create the right fit you may need an extra "shim" made of plywood so the stack of lumber comes out the proper dimension to fit your anvil. In my drawing I show how to do it if you have an even number of boards and the ends do not come out the same. Steve attached a metal strap to make "pockets" to hold tools. The threaded rod actually clamps the anvil in place. There are no nails or shims and the anvil sits on a bed of silicone caulking (really If you look at the ends of the anvil stand you will notice the 1/2" threaded rods that hold the thing together. I suggest using yellow carpenter's glue and glue coated nails. I'd forgotten that Steve's end boards were 1-1/2" taller than the others to retain the anvil.Įach board is offset about 1-1/2 to 2" as they are stacked up. NOTE: When I was making my drawing below I had not looked at this photo for a year. The unique and HANDY thing about this design is the offset Steve put in the pieces as he stacked them up. It is a solid section built up by laminating pieces of 2x12 framing lumber. This anvil stand was built by Steve Barringer of B2 Design in Mooresville, NC. There are numerous ways to build an anvil stand. OR have them available when we NEED a stand. Often after wind or ice storms you can have your choice of log sections if you ask and have a way to haul them home.ĭon't forget that a taller section of log is a handy stand for a swage block OR to carve depressions in the end for forming sheet metal.īut, we are not always so lucky to have windfalls of large logs available OR the chain saw to cut to size. The piece of oak was collected after an ice storm. This old German anvil is setting on an oak stump that was trimmed to fit. Most modern smiths prefer some degree of portability. When you do this you want to be VERY sure that you will not want to change your anvil location. In old shops with permanent forge and anvil locations longer sections of logs like this were often set deep in the ground. I prefer to be able to lift mine off the stand if needed. Some smiths strap their anvils down to reduce the ring. Usually there are some spikes driven in the stump to keep the anvil from walking off from vibration. This is a short section of log that sets on the ground and the anvil sets on top. The Peter Wright anvil on a red oak stand at top is a classic. I also kept size and weight in mind as well, since we know not everyone has the space to fit larger or heavier options.August 14, 2002, Appended 8/16, 9/7, 10/20, 2005 (updated may 28, 2011) I used this experience to assemble a list of options, and did my best to make sure I included a good range of vise styles, so whether you’re a woodworker, automotive hobbyist, or just someone who needs a solid, reliable vise, you should find something that works for you. I’ve used a variety of bench vises in my career as a residential carpenter. On the other hand, if you’re looking to secure large wood pieces, and don’t want to risk damaging their delicate surface, go with a dedicated woodworking vise. This feature is really convenient for using a hacksaw on metal pipes. This is a separate, angled jaw that makes it easy to clamp a round pipe, much easier than trying to secure it in the flat face, which can easily dent or misshape your pipe. On a similar note, what type of material are you going to be using in your vise? If you’re planning on working with metal piping, make sure to choose a model that has a pipe jaw. Keep in mind that “jaw width” may not be the same as “jaw opening." Take note of the jaw width of the vise, and make sure that it's large enough to be used for the projects you have in mind. By providing the ability to safely and securely hold nearly anything in place while you work on it, you’ll be able to tackle a variety of automotive, metal, or woodworking projects. They’re available in a few different styles and types, but essentially they’re just large clamps that are mounted directly to the top, side, or front of your workbench, and use a rotating screw to open and close their jaws. A reliable bench vise is one of the more useful accessories you can add to your workbench, and will probably end up being more convenient than you might think.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |